No filler spray cooling tower Products Overview Chengdu PAX Metallurgical Technology Co., Ltd. developed a series of filler spray cooling tower is to rely on the top of the motor fan forced cold air outside the tower, tower packing spray cooling tower the lower part of the air intake shutters suction column; uniform distribution of hot water by the water distribution system to the respective atomizer, the nozzle so that the hot water to the top of spray atomization, and into the tower of the air with the same to rise and heat exchange with rising droplet centralized cooling water into the sump by gravity naturally whereabouts to a certain height, then meet again to exchange heat with the cold air is on the rise, and the hot and humid air from the fan discharge tower. Second, no filler spray composition and characteristics of the cooling tower, the tower bearing parts: high-quality steel or concrete structure, the natural frequency 12HZ run the maximum amplitude is less than 0.09mm after taking galvanized steel coated paint the second floor of the epoxy asphalt to strengthen anti-corrosion measures. Envelope components: the selection of the material I produced fiberglass panel surface coated with color weather gel coat resin has excellent acid, alkali, salt and other corrosive chemicals can also not be rain and snow erosion result in performance degradation, long-term exposure to UV radiation, can withstand moisture, heat, cold and the impact of long-term use can still maintain its performance and color stability, and therefore very suitable for the chemical industry, salt spray corrosion coastal hit areas of the region as well as air pollution. 3 diversion hairdryer: kinetic energy recovery type, reasonable hairdryer curve makes reasonable air distribution, high efficiency, significantly recovered kinetic energy loss (36%) reduction in the loss of kinetic energy, hairdryer glass steel, lightweight, high strength, corrosion. 4 fans: the flow of less than 1,000 tons of cooling tower, the choice of high-strength aluminum alloy fan; flow greater than 1000 tons of cooling towers, should be used in glass fiber reinforced epoxy material fan blades for advanced airfoil fan gas reasonable power, air volume, smooth operation, low noise, high efficiency and corrosion resistance. The fan set fly-axis spacing devices, set security monitoring system (order separately), vibration, oil temperature, oil level monitoring function, the remote automatically display alarm and shutdown functions (with the the DCS signal output). Control mode control room centralized control and local control combine to achieve the monitoring, control, alarm, security chain. Motor: Tsinghua University, supporting and designed specifically for tons of cooling tower company 100-1000 the NGW-LF series cooling tower supporting special gear motor, its main structure for vertical monopole planetary transmission. Gear alloy structure, made of heat-treated high-precision machining. Has high strength, good toughness, and high precision; flow greater than 1000 tons of cooling towers should be used in the outdoor motor Y series horizontal reducer also oil temperature, vibration alarm device (oil level control needs to be reprovision). 6, atomizer professional technique successfully developed the YHS series special cooling tower atomizer: I, the selection of the atomizer according to the cooling water temperature, medium composition and concentration, and other conditions, respectively, selection of different material nebulizer (see atomizer material selection table), the atomizer nozzle 360 ??° adjustable, high strength, high temperature resistant, corrosion-resistant, water gas erosion, service life of more than 16 years of continuous operation for three years without maintenance. 7, the water collection device: my company for packing cooling tower wind capacity, a large amount of water characteristics, in particular developed specifically for this type tower efficiency and low resistance "YHS-II-type water collector, and obtained the national patent water collector piece no perspective phenomenon, received the bulk of the water is between closing the water tower body siding lap dense floating rate of less than 0.005% water. 8, diversion device: In order to reduce wind resistance, I developed a guiding device, particularly in key parts with large drag deflector, about a 20% reduction in drag. 9, antifreeze device: In order to enable the tower to adapt to the cold northern climate, my company, especially the installation of antifreeze device (ordering should explain in advance) in normal operation does not freeze in minus 40 degrees cold climate of the cooling tower. The filler spray cooling has the following characteristics: 1, the system resistance, air flow air volume, the gas-water contact area, cooling efficiency, easy maintenance: 4, applies to a wide range of the filler spray cooling tower to meet the different corrosion conditions, temperature drop of cooling water needs; also transform the original packing tower, the tower run effect of user requirements; Our company has a cooling tower design selection of cutting-edge talent, Design Institute and the user can provide special needs cooling tower type.